im english n id apreciate it if ppl say english cnt weld id outweld u silly scottish bastard anyday never beaten in a contest against any1 who has da same experiance as me sum1 i work wit has dun if for 25 years n im better so hows dat for english do i pass n better dan ur instucter my ass if u r dats 1 shit instructer
sori mate but i agree ur teachin wen u need 2 be taught for dat thickness voltage or heat as sum ppl are sayin even tho its wrong is fine but da wire speed is 2 high u do onli need 2 tack u dnt need to clamp n dem tacs lked lik dey wer jst pinchin it n its doesnt matter wether he used 1 hand or not wen i weld with 2 hands it looks da same as wen i weld wit 1 hand n not 2 be big headed or anything but im brilliant cuz im on £8 n hour n im 17
That goes for viewers alike! If you don’t know how to fucking weld, or aren’t consider a professional or do not know how to spell worth a fuck don’t waste our time with your comments!
That wasn’t all his fault. Look at the steel he is welding. It’s dirty and rusty, and that does effect the weld quality. Besides, he is welding in an uncomfortable position and welding one handed. He did preety good when you take that into consideration.
well i really hate talking bad about stuff but if i welded like that at where i work just once id get fired. the tacks shitty you only need two anyways the welds no fusion so no good there either and the wire speeds to fast for such low amprage so either crank that shit up or lower the wirespeed.
if any of you try pulse on pulse mig the best way to get a lovely bead is to weave bak and forth at the peak of the pulse wave, if you have a machine that gives you cc/cv wave form or cdt, once you learn the certain sounds of the arc, and the correct settings you will get a lovely weld with no spater, no haz (heat affected zone)and less distortion, remember bak and forth not side to side
Not trying to be an asshole but if you dont know how to do it, dont make an instructional video. You junk up the search results and then you just taught 11,000 people that its ok if your weld looks like shit and doesnt even fuse.
November 22nd, 2008
im english n id apreciate it if ppl say english cnt weld id outweld u silly scottish bastard anyday never beaten in a contest against any1 who has da same experiance as me sum1 i work wit has dun if for 25 years n im better so hows dat for english do i pass n better dan ur instucter my ass if u r dats 1 shit instructer
November 22nd, 2008
sori mate but i agree ur teachin wen u need 2 be taught for dat thickness voltage or heat as sum ppl are sayin even tho its wrong is fine but da wire speed is 2 high u do onli need 2 tack u dnt need to clamp n dem tacs lked lik dey wer jst pinchin it n its doesnt matter wether he used 1 hand or not wen i weld with 2 hands it looks da same as wen i weld wit 1 hand n not 2 be big headed or anything but im brilliant cuz im on £8 n hour n im 17
November 22nd, 2008
and for everyone saying the heat is too low its fuckin voltage so learn your shit before you criticise people
November 22nd, 2008
That goes for viewers alike! If you don’t know how to fucking weld, or aren’t consider a professional or do not know how to spell worth a fuck don’t waste our time with your comments!
November 22nd, 2008
where did they find this guy?
November 22nd, 2008
No it won’t. That steel was pretty thin, so there probably more than enough penetration.
November 22nd, 2008
That wasn’t all his fault. Look at the steel he is welding. It’s dirty and rusty, and that does effect the weld quality. Besides, he is welding in an uncomfortable position and welding one handed. He did preety good when you take that into consideration.
November 22nd, 2008
For something that thin? Not unless you turn the heat way down.
November 22nd, 2008
Go auto darkening welding helmut
November 22nd, 2008
shit welding man. more wire speed needed. that weld looked like something from my nose
November 22nd, 2008
ya my spelling not to good
November 22nd, 2008
penatrishion? whats that? you mean Penetration right?
November 22nd, 2008
there was no penatrishion that was shit if you drop it on the ground I bit it would fall apart
November 22nd, 2008
pulling gives better penetration, pushing is less penetration but a more shallow weld puddle. try the figure 8 pattern,
November 22nd, 2008
well i really hate talking bad about stuff but if i welded like that at where i work just once id get fired. the tacks shitty you only need two anyways the welds no fusion so no good there either and the wire speeds to fast for such low amprage so either crank that shit up or lower the wirespeed.
November 22nd, 2008
if any of you try pulse on pulse mig the best way to get a lovely bead is to weave bak and forth at the peak of the pulse wave, if you have a machine that gives you cc/cv wave form or cdt, once you learn the certain sounds of the arc, and the correct settings you will get a lovely weld with no spater, no haz (heat affected zone)and less distortion, remember bak and forth not side to side
November 22nd, 2008
well for a begginer like me ,its ok then
November 22nd, 2008
lets see all you lot weld then!!!!!!
November 22nd, 2008
u must be blind!
November 22nd, 2008
I thought the welds looked good better than what i can do
November 22nd, 2008
Not trying to be an asshole but if you dont know how to do it, dont make an instructional video. You junk up the search results and then you just taught 11,000 people that its ok if your weld looks like shit and doesnt even fuse.
November 22nd, 2008
Do you push or pull? When moving the tip, do you do circles or do you move the tip back and forth?
November 22nd, 2008
Wow, who knew that to be a brilliant internet-anonymous welding commentator you had to have a mouth like a toilet ?
Not me !
November 22nd, 2008
this kunt nos fuckall where i work those tacks would be considered as birdshit! they look like shit, two of the tacks didnt even fuse absolute shit
November 22nd, 2008
not to bad for such a shity seting
(sounds like popcorn = bad seting
sizzling bacon sound = good seting)