Try that little wire measuring thing on an oil rig test scenario…the Lloyds man would show you the way to the canteen..
But keep up the good work. 5 stars !!
whogotdro September 20, 2008
4:00 pm
Kudeghraw ; definatly finking on my wave length i set the amps according to the thickness of work im welding to then fine tune the speed but also remember weldings not about looks its about strength so get the amps as high as you can before burnthrough (unless your just welding for looks that is)
australianredneck September 20, 2008
4:00 pm
Ha Ha your funny mate any way fosters is shit vb is the shit and when I have drunk a lot I will than piss all over your mum with her mouth open and she will love it
Kudeghraw September 20, 2008
4:00 pm
No, the part that is ejaculating inside of your mum while you are raping a wallaby. Why don’t you go puke after drinking half a can of Foster’s. Everyone else does.
australianredneck September 20, 2008
4:00 pm
what sort of parts your mums dildo
Kudeghraw September 20, 2008
4:00 pm
I bet you think a little cold roll and a couple of holes of porosity is “good enough”. You would probably make $10/hr in my shop pushing a broom and deburring my parts…
australianredneck September 20, 2008
4:00 pm
your mum has bib boobs yum
41point2 September 20, 2008
4:00 pm
Is it necessary for you to be so rude and condescending? At least Kudeghraw offered a method with out being rude or presumptuous of this mans efforts to share Knowledge. You’re the ass hole in the shop, aren’t you? There’s always one that got to put others down to make himself feel better. I’m just learning Mig for fun right now and these little tips from both this gentleman in the vid AND Kudegthraw are very helpful. Okay your turn now say something else stupid.
australianredneck September 20, 2008
4:00 pm
Thats what I say well done this way he is saying is bull shit I think he is just trying to sound smart but truth be told he just needs a girl friend and get his cherry off
Kudeghraw September 20, 2008
4:00 pm
To be honest, I just set my amperage first. Then I pull the trigger with one hand and fine tune my wire speed with the other. It’s more than just sounding like frying bacon or whatever. You could be way off your settings for hard wire and it would still sound like bacon or eggs frying. You listen for the most consistent and stable sound possible.
khonlaox September 20, 2008
4:00 pm
just had to say i dont like this method because im not good at math but there is another way just find scrap metel set speed to low and start to up the speed until it starts to sound like your frying an egg this method varys with differnet metels
jplisson September 20, 2008
4:00 pm
Thanks, good tip.
cstacherski September 20, 2008
4:00 pm
HAhaha might not have no knobs and a pair of vice grips clamped on to it. hahahahahhaah been there. done that. good video!
Leave a Comment
If you would like to make a comment, please fill out the form below.
Try that little wire measuring thing on an oil rig test scenario…the Lloyds man would show you the way to the canteen..
But keep up the good work. 5 stars !!
Kudeghraw ; definatly finking on my wave length i set the amps according to the thickness of work im welding to then fine tune the speed but also remember weldings not about looks its about strength so get the amps as high as you can before burnthrough (unless your just welding for looks that is)
Ha Ha your funny mate any way fosters is shit vb is the shit and when I have drunk a lot I will than piss all over your mum with her mouth open and she will love it
No, the part that is ejaculating inside of your mum while you are raping a wallaby. Why don’t you go puke after drinking half a can of Foster’s. Everyone else does.
what sort of parts your mums dildo
I bet you think a little cold roll and a couple of holes of porosity is “good enough”. You would probably make $10/hr in my shop pushing a broom and deburring my parts…
your mum has bib boobs yum
Is it necessary for you to be so rude and condescending? At least Kudeghraw offered a method with out being rude or presumptuous of this mans efforts to share Knowledge. You’re the ass hole in the shop, aren’t you? There’s always one that got to put others down to make himself feel better. I’m just learning Mig for fun right now and these little tips from both this gentleman in the vid AND Kudegthraw are very helpful. Okay your turn now say something else stupid.
Thats what I say well done this way he is saying is bull shit I think he is just trying to sound smart but truth be told he just needs a girl friend and get his cherry off
To be honest, I just set my amperage first. Then I pull the trigger with one hand and fine tune my wire speed with the other. It’s more than just sounding like frying bacon or whatever. You could be way off your settings for hard wire and it would still sound like bacon or eggs frying. You listen for the most consistent and stable sound possible.
just had to say i dont like this method because im not good at math but there is another way just find scrap metel set speed to low and start to up the speed until it starts to sound like your frying an egg this method varys with differnet metels
Thanks, good tip.
HAhaha might not have no knobs and a pair of vice grips clamped on to it. hahahahahhaah been there. done that. good video!